RaspberryPi2EGLFS

A modern guide for cross-compiling Qt 5.6 for HW accelerated OpenGL with eglfs on Raspbian Jessie.

Note that this is not intended for running desktop-style, windowed Qt apps under X11, but rather for the real embedded/device creation use case where the Qt app runs fullscreen on top of dispmanx/EGL using the Broadcom drivers.

For detailed information about eglfs and Qt on Embedded Linux check the Qt documentation.

Step by step

1. Get the latest image from https://downloads.raspberrypi.org/raspbian_latest

2. Unzip and write it to a memory card. Replace ... with the SD card device (check dmesg).

sudo dd if=2015-09-24-raspbian-jessie.img of=... bs=4M

3. Boot it up, run raspi-config, change it to boot to the console instead of X, change the GPU memory to 256 MB, install a bunch of development files (for simplicity we use build-dep, not everything is really needed, but it is easier this way), and prepare our target directory:

sudo raspi-config

sudo nano /etc/apt/sources.list

and uncomment the deb-src line.

sudo apt-get update
sudo apt-get build-dep qt4-x11
sudo apt-get build-dep libqt5gui5
sudo apt-get install libudev-dev libinput-dev libts-dev

sudo mkdir /usr/local/qt5pi
sudo chown pi:pi /usr/local/qt5pi

4. Back on the host PC, create our working directory and get a toolchain:

mkdir ~/raspi
cd ~/raspi
git clone https://github.com/raspberrypi/tools

5. Create a sysroot. Using rsync we can properly keep things synchronized in the future as well. Replace IP with the address of the Pi.

mkdir sysroot sysroot/usr sysroot/opt
rsync -avz pi@IP:/lib sysroot
rsync -avz pi@IP:/usr/include sysroot/usr
rsync -avz pi@IP:/usr/lib sysroot/usr
rsync -avz pi@IP:/opt/vc sysroot/opt

6. Adjust symlinks to be relative. Instead of the old fixQualifiedLibraryPaths get a script that works:

wget https://raw.githubusercontent.com/riscv/riscv-poky/master/scripts/sysroot-relativelinks.py
chmod +x sysroot-relativelinks.py
./sysroot-relativelinks.py sysroot

7. Get qtbase (note that Qt 5.6 is not yet released and is work in progress) and configure Qt. The target directory is /usr/local/qt5pi on the Pi, the host tools like qmake will go to ~/raspi/qt5, while make install will target ~/raspi/qt5pi (this is what we will sync to the device). If using the old Pi instead of the Pi 2, change -device to linux-rasp-pi-g++.

git clone git://code.qt.io/qt/qtbase.git -b 5.6
cd qtbase
./configure -release -opengl es2 -device linux-rasp-pi2-g++ -device-option CROSS_COMPILE=~/raspi/tools/arm-bcm2708/gcc-linaro-arm-linux-gnueabihf-raspbian/bin/arm-linux-gnueabihf- -sysroot ~/raspi/sysroot -opensource -confirm-license -make libs -prefix /usr/local/qt5pi -extprefix ~/raspi/qt5pi -hostprefix ~/raspi/qt5 -v
make
make install

8. Deploy to the device. We simply sync everything from ~/raspi/qt5pi to the prefix we configured above.

rsync -avz qt5pi pi@IP:/usr/local

9. Build an example:

cd qtbase/examples/opengl/qopenglwidget
~/raspi/qt5/bin/qmake
make
scp qopenglwidget pi@IP:/home/pi

10. On the device, let the linker find the Qt libs:

echo /usr/local/qt5pi/lib | sudo tee /etc/ld.so.conf.d/qt5pi.conf
sudo ldconfig

11. Still on the device, fix the EGL/GLES library nonsense:

The device may have the Mesa version of libEGL and libGLESv2 in /usr/lib/arm-linux-gnueabihf, resulting Qt apps picking these instead of the real thing from /opt/vc/lib. This may be fine for X11 desktop apps not caring about OpenGL performance but is totally useless for windowing system-less, fullscreen embedded apps.

sudo rm /usr/lib/arm-linux-gnueabihf/libEGL.so.1.0.0 /usr/lib/arm-linux-gnueabihf/libGLESv2.so.2.0.0
sudo ln -s /opt/vc/lib/libEGL.so /usr/lib/arm-linux-gnueabihf/libEGL.so.1.0.0
sudo ln -s /opt/vc/lib/libGLESv2.so /usr/lib/arm-linux-gnueabihf/libGLESv2.so.2.0.0

You may want to save the originals somewhere, just in case.

12. Run qopenglwidget we deployed to /home/pi. At this point it should just work at fullscreen with 60 FPS and mouse, keyboard, and possibly touch support.

13. Build other Qt modules as desired, the steps are the same always:

~/raspi/qt5/bin/qmake -r
make
make install

then deploy the new files by running

rsync -avz qt5pi pi@IP:/usr/local

in ~/raspi

Additional notes

Frequently asked question: I only get a low resolution like 640x480 or even 576x416 with black boxes. How to fix this?

As a quick fix, try adding disable_overscan=1 to /boot/config.txt and after a reboot check with /opt/vc/bin/tvservice what modes are available. For example, to switch to 1024x768:

$ /opt/vc/bin/tvservice -m DMT
Group DMT has 4 modes:
           mode 4: 640x480 @ 60Hz 4:3, clock:25MHz progressive 
           mode 9: 800x600 @ 60Hz 4:3, clock:40MHz progressive 
           mode 16: 1024x768 @ 60Hz 4:3, clock:65MHz progressive 
           mode 35: 1280x1024 @ 60Hz 5:4, clock:108MHz progressive 
$ /opt/vc/bin/tvservice -e "DMT 16 HDMI"
$ fbset -xres 1024 -yres 768

Troubleshooting

Enabling the logging categories under qt.qpa is a good idea in general. This will show some debug prints both from eglfs and the input handlers.

export QT_LOGGING_RULES=qt.qpa.*=true
./qopenglwidget

A typical output would like like this:

qt.qpa.egldeviceintegration: EGL device integration plugin keys: ("eglfs_brcm", "eglfs_kms")
qt.qpa.egldeviceintegration: EGL device integration plugin keys (sorted): ("eglfs_brcm", "eglfs_kms")
qt.qpa.egldeviceintegration: Trying to load device EGL integration "eglfs_brcm"
qt.qpa.egldeviceintegration: Using EGL device integration "eglfs_brcm"
Unable to query physical screen size, defaulting to 100 dpi.
To override, set QT_QPA_EGLFS_PHYSICAL_WIDTH and QT_QPA_EGLFS_PHYSICAL_HEIGHT (in millimeters).
qt.qpa.input: libinput: input device 'Logitech Optical USB Mouse', /dev/input/event0 is a pointer caps = relative-motion button
qt.qpa.input: libinput: input device 'Apple Inc. Apple Keyboard', /dev/input/event1 is a keyboard
qt.qpa.input: libinput: input device 'Apple Inc. Apple Keyboard', /dev/input/event2 is a keyboard
qt.qpa.input: libinput: input device 'Raspberry Pi Sense HAT Joystick', /dev/input/event3 is a keyboard
qt.qpa.input: Using xkbcommon for key mapping

Verify that eglfs_brcm is in use and that input devices are correctly found.

When using a touchscreen, setting the correct physical screen size may be essential to get properly scaled, finger friendly user interface elements with Qt Quick Controls. When using ordinary monitors via HDMI, the default 100 dpi may be acceptable.

It is also wise to carefully check the output of configure (saved as config.summary) before proceeding to build qtbase. Check that the following are marked as 'yes':

Support enabled for:
  ...
  Evdev .................. yes
  FontConfig ............. yes
  FreeType ............... yes (system library)
  ...
  libinput................ yes
  ...
  OpenGL / OpenVG: 
    EGL .................. yes
    OpenGL ............... yes (OpenGL ES 2.0+)
  QPA backends: 
    EGLFS ................ yes
      ...
      EGLFS Raspberry Pi . yes
    ...
    LinuxFB .............. yes
    ...
  udev ................... yes
  xkbcommon-evdev......... yes

Regarding keyboard input

By default Qt attempts to disable the keyboard and hide the cursor on application startup. This is very handy since this way keystrokes will not go to the console (which is enabled by default in a normal Raspbian image) "underneath". However, at the moment this will all silently fail when starting an application remotely via ssh. This is the explanation for the (harmless) 9;15] and similar prints and the keyboard input unexpectedly going to the console as well. As a workaround, start apps directly on the console. Alternatively, get rid of all the TTYs by editing /etc/systemd/logind.conf to contain NAutoVTs=0 followed by sudo systemctl disable getty@tty1.service and a reboot.