Talk:Setting up Gerrit: Difference between revisions

From Qt Wiki
Jump to navigation Jump to search
Line 51: Line 51:
It's not intuitive that someone needs to search the Gerrit page to find instructions on how to configure their git.
It's not intuitive that someone needs to search the Gerrit page to find instructions on how to configure their git.


Side note, is Gerrit only used for Qt 5? Or is this page just outdated and in need of updating with Qt 6? (A likely byproduct of the fact that the cloning instructions are on a page that no one would think to search for)
Side note, is Gerrit only used for Qt 5? Or is this page just outdated and in need of updating with Qt 6? (A likely byproduct of the fact that the cloning instructions are on a page that no one would think to search for) --[[User:Mairtin|Mairtin]] ([[User talk:Mairtin|talk]]) 06:48, 5 December 2023 (UTC)

Revision as of 06:48, 5 December 2023

  • It is bad form to tell users to make `--global` git configuration changes to conform to the policies of a single project. Sparr (talk) 06:00, 18 December 2018 (UTC)
  • Firstly, most of the settings are entirely uncontroversial. Some should be just git defaults (some are meanwhile). Secondly, anyone who seriously works on Qt will have 50+ Qt repositories, which easily dwarfs everything else they have on their disk, so the pragmatic choice is to make the Qt settings the global default and override them where necessary. Ossi (talk) 07:47, 12 September 2019 (UTC)


doc not clear?

Under "Local Setup", in the last step, it says:

> If the connection is functional, every Gerrit event should be displayed

But it gives no explanation of "every gerrit event" nor what the output might look like.

After I did all the above steps successfully, i issued the last command ssh codereview.qt-project.org gerrit stream-events, and my terminal just sat there, showing no output, doing nothing, and did not return to the command prompt.

What is expected here? DHLaw

the instructions have been indeed botched up; i haven't been watching closely enough. will fix now. Ossi (talk) 11:12, 8 January 2021 (UTC)

two separate SSH keys?

in the section "How to get started - Gerrit registration", step 5 says "Go to "Settings"-> "SSH Public Keys" and upload your public SSH Key". You'll note that the link for "public SSH key" points to github, which instructs the user to create a key named "ed25519". After that we are told to add it into the "gerrit->ssh keys" section. So far so good.

But then below, in the next section "Local Setup", we are instructed to create another SSH key named "id_rsa", and also add that into the "gerrit->ssh keys" section. Is this correct? we are to have two keys with different names?

What is Gerrit and why set it up?

I came across this page from the Boot2Qt instructions. What is this page, what is Gerrit, and why do I care? As it stands, this page is a stand-alone page with no clear explanation for why it even exists.

Proposal

  • Add an explanation of what Gerrit is
  • Add a table of contents that links this step to other related info
  • Also add a previous and next page
  • Add "See also"

Example table of contents: Getting started with contributing to Qt

  • Create a Qt account (page link)
  • Something (page link)
  • Something (page link)
  • Setting up Gerrit (bolded)
  • Something (page link)
  • Something (page link)

--Mairtin (talk) 06:38, 5 December 2023 (UTC)

Move git cloning (etc) to it's own page?

Is there a reason that the git setup is on this page? It's not intuitive that someone needs to search the Gerrit page to find instructions on how to configure their git.

Side note, is Gerrit only used for Qt 5? Or is this page just outdated and in need of updating with Qt 6? (A likely byproduct of the fact that the cloning instructions are on a page that no one would think to search for) --Mairtin (talk) 06:48, 5 December 2023 (UTC)